The Evic VTC mini by Joyetech is the latest device mod that is a much smaller version of the previous devices VT that had a built-in battery, except this version uses replaceable single 18650 batteries.

The mod was sent for purposes of review by gear best, its available for $50.99 in the kit version from the China warehouse
also available for $51.97 from the EU warehouse based in the
the cyan (blue) version costs a bit more at the EU warehouse at the moment though for $53.06

It’s a nice small mod that does 1-60 watts as well as temperature control for both nickel and titanium. The white version has a subtle metallic finish and is not too slippery in hand and is not a fingerprint magnet. One of the best things about the device mini is the large screen that displays the power or temperature; the voltage applied, the resistance and the battery meter. The button is a decent size but with a nice firm click that doesn’t take too much force to press. The battery door is quite thick and held on with strong magnets and can be opened by grabbing the sides of the door and pulling it out or by using a nail to flip it out from the bottom of the mod. There are no huge venting holes noticeable however at the bottom of the mod there two slots that lead into the battery area.

There’s a micro USB port for charging and upgrading the firmware. The 510 is ss and spring loaded too. To turn the device on or off its five clicks of the fire button and to enter the menu click three times and the first selection will flash. Press the right button or + to switch between nickel, titanium, regular view or bypass mode. Bypass mode allows you to use the mod as a mech where the wattage limit is dictated by your battery spec. Press the fire button to then lock in the setting that you have chosen. In temp mode it’ll display the temperature that can be adjusted by pressing left or right. You can also lock the Atty resistance in vt mode by entering the menu and clicking left twice and then pressing right when you get to the resistance, and it’ll display the lock symbol, just make sure the patty is at room temp when locking the resistance.

When changing Atty press fire button with no Atty attached to reset, the mod will ask new coil right, the same coil left. The max initial wattage can also be adjusted in temp mode. In the menu press left once, it’ll then flash the wattage that can be adjusted by clicking the right button, however it seems to only scroll up in wattage, to get to lower watts you have to scroll to 60w then click right again and it’ll be back at 1 watt so you can scroll up again. The mod also automatically shifts to power mode when the coil is above 1ohm. You can display the vapor time and puff counter by going to the 3rd option in the menu that shows the battery indicator and then pressing right to shift through the vaping time and puff counter. You can also reset either of those values by pressing the fire button when the puff counter or vaping time is showing – if you don’t want either to be reset get to the battery indicator and then click the fire button there.

Some specs:
watts mode – 1-60w, 0.1ohms-3ohms also the same resistance for bypass mode
temp mode 0.05ohms-1ohm, 100c-315c, 200-600f
1×18650 battery
micro USB port
22.2mm x38.2mm x82mm
even mini vtc 18650 battery
the evic mini magnetic battery cover
protection:
10-second cutoff, Atty little protection, weak battery alert (mod will show the battery as empty at 3.3v) In practice it can be a bit lower, however, around 3.1v. Displays an Atty low alert when resistance is below 0.05 ohms in tc mode or 0.1 in view mode. The mod also protects the board temperature if it goes above 70c. The mod says it charges at 1amp too, but in practice, it charges a bit lower around 0.85a. In temp mode there’s also a warning when the temp has been reached where it says temp protection and will reduce the watts down.


The device mini kit comes with the mod, USB cable and the ego one mega atomizer with had the ni200 coil (0.2ohms) installed as well as a titanium coil (0.4ohms) in the box. It’s nice that it matches the color of the mod and is a good way to test the temperature control out. You can also buy separate heads for it as well as the car heads that are quite easy to rebuild with. The patty itself is quite short which looks good on the mod being small. Also, the airflow is adjustable with two slots that can be decent for an mtl vape at the lowest settings, however it’s not as large overall compared to other tanks around now. The coil heads have four juice flow holes too but are quite small so would struggle with very high VG juices and wicking with higher wattages. The tank is easy to fill though by unscrewing the base as well as to change coils. The tank itself though is a 1 piece system with the tank section top cap and chimney tube all stuck together similar to how many tanks in the past used to be. It can be cleaned out but maybe not as easily as ones that can be disassembled completely.
ego one mega sub ohm tank base ni200 nickel coil head
ego one mega sub ohm temperature control tc tank coil head 0.2ohms
ego one mega tank inner tube
joyetech ego one mega sub ohm tank in white
Overall its a nice mod to use, one of the smallest mods out that takes an 18650 and fairly light too. It also feels quite solid with no rattly buttons and the battery door sits very secure. The body also seems to be made well with no gaps and is quite thick. The screen is great as you can read it a lot easier than other mods’ screens. Its great also that there firmware upgrades and it supports nickel and titanium out of the box. Maybe there will be support for other wire types in the future with upgrades. The kit coming with a matching tank is a nice option too that makes it good value as well as the choice of 3 colors of the mod.

LEAVE A REPLY

Please enter your comment!
Please enter your name here